TASCA [ MORE REVIEWS ] [ WEBSITE ] [ NEW STORIES ]

In-Box Review
135
M4A3(76)w Sherman
U.S. Medium Tank M4A3(76)W Sherman
  • move

by: Stefan Halter [ DANGEROO ]

Introduction

After Tasca’s series of the M4A4, M4A1 and the M4A2, the logical step from a molding perspective would have been an M4 or maybe an early M4A3. In this sense Tasca’s announcement of the imminent M4A3(76)w release came as somewhat of a surprise to many of us, but it is of course a necessary step towards the full range of Sherman kits. Unlike the previous releases, this version needs a completely new upper and lower hull as well as a new turret. On the other hand, many of these molds can be used for other versions as well, such as M4A1(76) and M4A2(76) Shermans.

There is no need to recite the history of the Sherman tank at this point as most of you will already know it. This version was used mainly by the US Army in Europe, and later variants had the new HVS-suspension with wider tracks. This version has been served by other manufacturers before, most notably the aging but still useful Italeri kit (often re-boxed by other manufacturers) and two installments by Dragon (the older Battle of the Bulge kit No. 6255 and the newer premium edition No. 6325).

review

The box contains 18 sprues in olive drab plastic, two small clear sprues, 4 pieces of vinyl tracks, a PE fret, poly caps, a piece of foam rubber and the decal sheet, so we have a lot of ground to cover. Most of these sprues are packaged in one bag each, which is highly commendable. There are no sink marks, flash or knock-out nodes nor pin marks in places they can be seen later. The usual mold seams are easy to remove and in many cases barely noticeable. The instructions are easy to follow line drawings with options clearly pointed out.

Tasca has an interesting way of molding, as some areas of a sprue are exactly the same as we’ve seen in other kits and other parts are new. This is most notable on sprue C (x1) which contains some parts for earlier Shermans, which will go to the spares box, and also quite a few M4A3/47° hull specific parts. Sprue D/G (x2), on the other hand is one we’ve seen before in other kits. The G part however can be found separately in the kit in 3 different versions in clear and olive drab plastic. Other M4A3 specific parts are on sprues H (upper hull and sponson floors) and O (engine deck and exhaust parts). Sprue J has the transmission cover and the parts for the 76mm turret, while another Sprue H contains the turret shell.

Construction begins with the fully working suspension with each of the 6 bogies composed of 15 parts and foam rubber inserts to get the working effect. The suspension was released before as set 35-008. Sprue B (x3) contains all the parts for the bogies, while sprue A (x2) has the drive sprockets and the idlers. The bogies are the appropriate raised return roller type and have nice foundry markings and the three bottom bolts. There are two options of road wheels with either the pressed solid spoked type or the smooth dish type. All wheels (including the idler) have rear inserts and the road wheels can be fitted with the small rivets along the inside. The kit also includes all three possible variants of the drive sprockets. The kit comes with a T48 track with two parts per side that should be glue-able with normal plastic cement. The T48 track is adequate for this version. There are no duckbill end connectors.

The lower hull is constructed next, and as we’ve become used to with Tasca, it is constructed from separate parts for the floor, sides and back. These are all contained on sprue E. The idler mounts are a wonderful slide molding with delicate details. Tasca recommends not to glue these in place so the track tension can be adjusted later on. The exhaust deflector is made up of 6 parts and must be the most detailed exhaust deflector in plastic I’ve seen so far. On the front end, the one piece transmission cover has subtle cast texture, though some may wish to increase this even more as it is very subtle and regular. There are no foundry markings on this part.

The upper hull is finely molded with foundry marks where necessary. There is no weld seam on the side where the front armor plate is attached to the sides. Weld seams on top of the hull on the other hand are correct with raised details. There are detailed inserts for the sponson floors.

The hull machine gun is slide molded with muzzle depression and can be mounted movable. Lights are provided in plastic with the lenses separately in clear plastic. The modeler has a choice of either plastic or PE for the light brush guards. Fenders are provided separately and very finely molded. Driver and hull machine gunner’s hatches are detailed with either clear or normal plastic periscopes and protective guards from PE. The instructions give you details on how to improve the hatch with handles from wire, but no wire (or any handles in plastic) is included.

Moving along the sides to the rear: sand guard mounting strips are provided in plastic and seem a bit on the thick side (although very thin for plastic parts). PE would maybe have served this part better. The back armor of the hull is a separate part and the engine deck is provided separately from 4 parts indicating more versions of the 47° hull Sherman on the way. The engine bay doors could be modeled open for those wanting to mount an engine. There is an option for early or late type engine deck (with the back part of it either made up of one or two panels), and handles are provided in plastic here. Armored fuel caps are provided separately with detail underneath. The rear lights are in normal plastic with the guards again either in plastic or PE. The tools are nicely detailed items, but there are no straps and these will have to be sourced elsewhere. The tie downs where the straps go on the other hand, are molded with the upper hull.

The turret assembly starts with the gun barrel. The modeler has the choice of two different barrels, either the earlier smooth muzzle M1/M1A1 barrel or the later M1A1C /M1A2 with muzzle brake thread protector. No muzzle brake is provided. Unfortunately the barrels are made up of two halves and care will have to be taken to get a correct alignment and profile. The gun mantlet again has a very subtle cast texture and is also missing the foundry marks. There is no gun breech, and no other interior details are provided.

The turret itself is constructed in the usual fashion of upper and lower halves and again has subtle cast texture and foundry marks where appropriate. It is the earlier type turret with the two large hatches (the later commander’s cupola with periscopes and the ring mount with .50 cal. machine gun) which is correct for the gun barrels provided. The ring mount includes detailed hatches with periscope and handles inside and out. And of course the Tasca .50 cal. MG is still the best plastic representation of the “ma duce” I have seen to date, see the separate review here:
Tasca .50 cal. MG

The commander’s cupola can either be built from a clear plastic part or a normal part. The sprue and part are identical, just a different type of plastic. The lid unfortunately has hardly any interior detail and no periscope. Again there are instructions to make the handle from wire but no wire or plastic alternative provided.

The pistol port is correctly integrated into the turret (unlike the Italeri offering). There is a mold line around the pistol port, which I am unsure whether it represents an original mold line or is just a leftover from the slide molding process. I am assuming the latter as I have not seen anything like it in photos of the original. These should prove easy to sand off. Detailed instructions are given, as to how to mount the machine gun on the back of the turret in the stored position (and of course there is a full length separate MG barrel for this as well).

As a little bonus the kit also includes 4 of Tasca’s nicely detailed US jerry cans (2 water and 2 gas). These are also sold separately as kit 35-L14, see review here:
US Jerry Cans

Markings:
Markings are provided for three different versions, all in olive drab with a full complement of stars (with those of the first example “scratched” off). The three different options are:

• C Company, 69th Tank Battalion, 6th Armored Division 1944-45,
• C Company, 761st Tank Battalion, Nancy, France, November 1944,
• C Company, 774th Tank Battalion, 3rd Armored Division, Bovigny, Belgium, January 1945.

The decals are printed by Cartograf and the instructions point out - where possible - which alternative parts to use for which version.

Conclusion

This is certainly a beautifully engineered kit from which I expected a lot. I was somewhat disappointed by the barrels and some missing foundry marks as these would certainly have lifted this kit above the others available. Also the cast effect seems very smooth (although American casting was known to be smooth) and many may wish to increase the effect somewhat.

With the price of this kit about 50% higher than the comparable Dragon offering at a major Asian online store, I am inclined to say that the modeler will get more for his money elsewhere. This is especially true considering the Dragon offering has two types of turret, a metal barrel and muzzle brake. However, I will leave this decision to each modeler and again repeat that it is certainly a beautiful kit with a wealth of details and should prove well worth building.

Therefore, I have mixed feelings regarding the rating: The kit is well worth a 90% but due to the price and comparison to other offerings it only receives a “recommended” and not a “highly recommended”.

References:
There is a wealth of literature on the M4. Some relatively easy and inexpensive to get are:

M4 (76mm) Sherman Medium Tank 1943-65, Steven Zaloga, Osprey New Vanguard
The M4 Sherman at War, Steven Zaloga, Concord Publications
The Sherman at War (2), Steven Zaloga, Concord Publications
Walk Around M4 Sherman, Jim Mesko, Squadron/Signal Publications
Sherman in Action, Bruce Culver, Squadron/Signal Publications
SUMMARY
Highs: Beautifully engineered and detailed, suspension, .50 cal. MG.
Lows: Two part barrels, some missing foundry marks; price!
Verdict: Recommended.
Percentage Rating
90%
  Scale: 1:35
  Mfg. ID: 35-019
  Suggested Retail: $65 US
  PUBLISHED: Jul 18, 2010
  NATIONALITY: United States
NETWORK-WIDE AVERAGE RATINGS
  THIS REVIEWER: 84.62%
  MAKER/PUBLISHER: 92.94%

Our Thanks to Tasca!
This item was provided by them for the purpose of having it reviewed on this KitMaker Network site. If you would like your kit, book, or product reviewed, please contact us.

View Vendor Homepage  |  More Reviews  

About Stefan Halter (Dangeroo)
FROM: ZURICH, SWITZERLAND

I'll build just about anything military related that gets my interest, though most of it is 1/35 scale WWII Allied.

Copyright ©2021 text by Stefan Halter [ DANGEROO ]. All rights reserved.



Comments

Does anyone know what aftermarket barrel would fit this kit?
JUL 20, 2010 - 07:20 AM
Thanks for the review Stefan. think i'll grab me a DML kit after what you've said. cheers!
JUL 20, 2010 - 07:40 AM
Glad I could help gentlemen! Jon, I don't have any AM barrels laying around but I will check if the DML BoB-Sherman's metal barrel will fit. If it does, anything good for the DML kit should be fine for this one as well. Cheers! Stefan
JUL 21, 2010 - 07:53 PM
I tried the fit of the Dragon barrel and it was a bit of a loose fit. Also the barrel seem to be attached farther back on the Tasca kit than on the DML, so the barrel will be a it shorter. I'm certain it could be adapted (by adding a collar for one thing) but it won't be a smooth shake and bake job. HTH! Cheers! Stefan
JUL 22, 2010 - 07:51 PM
Stefan, first of all: Thanks for your review! I assume this will influence the audiance in preferring the DRAGON M4A3 76-MM Wet kit. But you couldn't convince me. I have both kits and a build the TASCA M4A3 recently. I was impressed by TASCA's superb engineering and the wealth of details! Stefan, you are correct in so far that the DRAGON model is cheaper! In my opinion, this is the only advantage of the DRAGON kit. Compare the DRAGON model's running gear with the Tasca one! I give you an example; - the three bolts on the bottom of the volute spring assy. DRAGON one's show closer resemblance to mud pieces then bolts. TASCA is the only model company that has the correct degree of the levers of the volute spring assy. TASCA's exhaust grill builds into a perfect scalled down piece and is even workable! Compare the inside of the driver's and co-driver's hatches and or the periscopes M4A1 with the TASCA's one and you will see the difference. The DRAGON parts are crude and not as detailled as the TASCA's one. Not to mention the M2 HB .50 CAL Machine Gun. Tasca's one is a beauty and the best .50 CAL in model even better then the CAL SCALE one's. The DRAGON one's looks more like a toy. These examples, and these are not the only one's, are factors, that make me to prefer the TASCA kit. But this is my personal opinion. Cheers Hauke Krapf
JAN 11, 2011 - 10:47 AM
I agree with all over you points Hauke, as well as all those who have made them previously. What's amazing to me is that by correcting a few little details TASCA has the potential to create what is for all practical purposes a perfect kit, and I encourage them to continue to pursue this
JAN 11, 2011 - 11:03 AM
Thanks for the review, I don’t mind the short comings as it still looks like an excellent kit. I would say that my biggest grip would be the lack of “Duck Bills” on the track. I’m with tom, I will shop around for the best price, but will defiantly and a couple to the Sherman stash.
JAN 11, 2011 - 06:04 PM
Thanks for the input Hauke, it's always good to have someone else's opinion. Like I said in the review, it's a great kit, but pricey. So if you can shop around and get it cheaper, go for it! Cheers! Stefan PS: No intention of influencing the audience in any direction, I was just stating my personal opinion. Just like you did, it's every one's own job to form their own opinion.
JAN 12, 2011 - 04:35 AM
I do not know what price has to do with scale, details, finish, or anything else to do with the quality of a model when recommending it. Price is relative to the efforts taken by the manufacturer to produce the kit and would be the last consideration to one who is recommending quality.
FEB 23, 2011 - 06:05 AM
   
ADVERTISEMENT


Photos
Click image to enlarge
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
ADVERTISEMENT